Plaster 25kg Historical Building HM 12
Historical plaster HM12:<ul><li>Especially suitable for buildings constructed in the Baltic states up to the 18th century.</li><li>For restoration of masonry and plaster on historical buildings</li><li>Lime-cement plaster mortar for renovation works</li><li>For weak and porous substrates</li><li>High water vapour permeability</li><li>Reinforced with polypropylene fibre</li><li>Cement content does not exceed 4%</li></ul>Application:<ul><li>The surface to be renovated must be dry, cleaned of dirt, grease, lichens, and paints</li><li>Alkyd-based coatings must be mechanically removed from the entire surface</li><li>Cracks and brick masonry joints must be thoroughly cleaned of atmospheric dirt</li><li>Crumbling parts must be removed down to the firm layer of the surface</li><li>Cracked and non-homogeneous materials are recommended to be removed mechanically or with a high-pressure washer</li><li>The old plaster layer destroyed by salts must be cleaned 1 m above the upper line of efflorescence</li><li>Treat the old plaster with SAKRET TGW primer</li><li>SAKRET HM 12 is a free-flowing consistency material</li><li>The mortar can be prepared with a mixer, concrete mixer, or mortar preparation and application equipment offered by SAKRET SERVISS</li><li>Mix the mortar for 3 - 5 minutes until a homogeneous consistency is achieved</li><li>Layer thickness from 5 to 20 mm (single layer thickness 5 - 12 mm)</li><li>Do not add lime, cement, or concrete-improving additives to the dry mix</li><li>Do not use dirty equipment or bags stored in improper conditions or previously opened for preparing the plaster</li><li>Technical data refer to a temperature of +20°C and 50% relative air humidity (lower temperature increases, higher temperature decreases the stated values)</li><li>During the mortar hardening phase, protect from sunlight, draughts, and excessively high temperatures (>30°C)</li><li>Protect fresh mortar from rain and excessively rapid drying</li><li>Once the mortar has started to set, no more water may be added</li><li>Immediately after use, wash containers and tools with water</li><li>Hardened mortar can only be removed mechanically</li><li>Contains cement, reacts alkaline</li><li>Protect skin and eyes, follow technical instructions. If mortar gets into eyes, rinse with plenty of water; consult a doctor if necessary</li><li>Protect packaging from weather conditions, store on wooden pallets in a cool and dry place, cover torn packaging immediately</li></ul>Technical Data:<ul><li>Cement content in dry mix ≤4%</li><li>Volume of prepared mortar ~ 18 l</li><li>Strength class CS I</li><li>Consumption ~14.2 kg/m² (at a layer thickness of 10 mm)</li><li>Grain size ≤ 1 mm</li><li>Full strength achieved after 28 days</li><li>Drying time 24 h</li><li>Air content in fresh mortar ≥ 14%</li><li>Fire safety class Euroclass A1 (non-combustible)</li></ul>
7.29 €
EUR
SKU: 243800
Brand: Sakret
EAN: 4751006564565
- Knauf Gypsum Plaster 30kg MP-75
- Knauf Gypsum Plaster 30kg Rotband
- Knauf Gypsum Plaster 5kg Rotband
- Dec. Plaster MRP-E 2mm 25kg (Scratch)
- Dec. Plaster SBP 2mm 25kg (cottage cheese)
- Pigment for Plaster Tinting 200g 920-3
- Pigment for plaster tinting 200g 4960-2
- Pigment for plaster tinting 200g 4960-1
- Pigment for plastering tinting 200g 920-1
- Pigment for Render Tinting 200g 01-3
- Pigment for Plaster Tinting 200g 01-2
- Pigment for Plaster Tinting 200g 130-3
This product is available at Zum.lv - the largest online store in Latvia.
View product on site