Adhesion Primer Luotto Tartuntapohja Aqua 1l
<p>Water-based primer for priming non-absorbent surfaces in interior use. Water-based adhesion primer for interior use on substrates with poor adhesion. Can be used on new or previously painted surfaces. The topcoat must be water-based and must meet the requirements for use, for example, when priming bathroom wall tiles, the last 2 coats must be painted with a moisture-resistant wall paint (Akzent SPA, Akrit 20). The finish coat is painted according to requirements. The paint can also be used as a final coat in areas where high wear resistance and moisture resistance are not required.</p><u>Properties:</u><ul><li>Acrylic primer</li><li>Almost odourless</li><li>Provides good adhesion to the finish coat</li><li>Use as an adhesion primer on new or previously painted surfaces</li><li>Contains anti-corrosion additives</li><li>Can also remain as the final finish coat</li><li>Colour - white (tintable in the Eskarocolor system)</li><li>Maximum VOC content in ready-to-use paint <140 g/l</li><li>Coverage 5 - 10 m²/l depending on surface type, surface preparation and porosity</li><li>Package volume 0.9 l</li></ul><u>Suitable surfaces:</u><ul><li>Glass</li><li>Ceramic wall tiles</li><li>PVC plastic</li><li>Laminate</li><li>Fibreglass</li><li>Aluminium</li><li>Melamine boards</li><li>Galvanised sheets</li><li>Surfaces previously coated with alkyd or catalyst paint</li></ul><u>Application:</u><p>The new surface must be clean, dry and free of rust. The presence of moisture (including condensation) on the surface to be painted is not acceptable. To clean dirty, dusty and black surfaces, use EasyClean. Clean greasy surfaces with a solvent (denatured alcohol). To clean galvanised surfaces, use Katto Cleaner. If necessary, use Biotol E or Biotol Spray for mould removal. Sand glossy surfaces with sandpaper and remove sanding dust.</p><p>For previously painted surfaces, remove loose and poorly adhered paint. Continue preparation as for a new surface.</p><p>Stir the paint thoroughly before use. When applying to the surface, the temperature of the substrate, air and paint must be between +10 and +30 °C and the relative humidity below 80%. When applying the first coat or spraying, the paint can be diluted with water by up to 5% by volume, nozzle diameter 0.013 - 0.015 inches. Apply to the surface with a brush, roller or paint sprayer, 1 - 2 coats. Before applying the next coat, make sure the previously painted coat is completely dry. During painting, prevent moisture from penetrating the surface, avoid drafts and the use of heaters (high temperature).</p><p>After finishing work, clean tools immediately with soap and water. Dried primer can be removed mechanically.</p><p>Drying time at +20 °C and 50% relative humidity - dry to touch after 1 h, can be repainted after 6 h.</p><p>The surface reaches its final wear resistance in approximately four weeks. During this time, cleaning of the surface should be avoided. If absolutely necessary, the surface can be cleaned earlier with a soft sponge or cloth and lukewarm water, but no earlier than two days after painting. Use water and a neutral detergent to wash painted surfaces. Do not use organic solvents, abrasive cleaning agents, or abrasive sponges or brushes.</p>
13.69 € EUR
11.49 € EUR
(-16%)
SKU: 209677
Brand: Eskaro
EAN: 6430066630646
- Adhesion Primer Luotto Tartuntapohja Aqua 0.45l
- Primer-Enamel Proteksol 50 0.9L for Metal Brown
- Primer-Enamel Proteksol 50 0.9L for Metal Black
- Primer-Enamel Proteksol 50 0.9L for Metal Grey
- Primer-Enamel Proteksol 50 0.9L for Metal Green
- Primer-Enamel Proteksol 50 2.7L for Metal Black
- Primer-Enamel Proteksol 50 2.7L for Metal Grey
- Primer-Enamel Proteksol 50 2.7L for Metal Green
- Primer GF-021 0.45L Alkyd Anti-Corrosion Red-Brown
- Primer GF-021 0.9L Alkyd Anti-Corrosion Red-Brown
- Primer GF-021 2.7L Alkyd Anti-Corrosion Red-Brown
- Paint Alukid 0.45L Silver
This product is available at Zum.lv - the largest online store in Latvia.
View product on site