Self-leveling compound mira 6600 cemplan 15 kg 0-10mm
<p>Fine-grained self-leveling compound for a particularly smooth and thin layer. 6600 cemplan is recommended for creating a smooth and even layer on concrete, screed, and old tiles.</p><u>Properties:</u><ul><li>Fast-setting</li><li>Cement-based</li><li>Polymer-reinforced</li><li>Good adhesion</li><li>Wear-resistant</li><li>Pumpable</li><li>Suitable for use under thin floor covering materials</li><li>Average consumption 1.6 kg/m²/mm</li><li>Layer thickness 0.5 - 10 mm</li><li>Application temperature from +10 to +20°C</li><li>Working time 20 - 30 min</li><li>Setting for light load 1.5 - 2 h</li><li>Further processing after 24 h</li><li>Waterproofing application after 12 - 18 h</li><li>Compressive strength 30 N/mm²</li><li>Flexural strength 6 N/mm²</li></ul><u>Application:</u><p>6600 cemplan can be used on concrete surfaces, their coverings, as well as old tiling and other surfaces with possible moderate movements or deformations. The substrate must be firm, dry, hard, and free from dust, dirt, grease, etc. Any crumbling parts of the concrete substrate must be removed; loose and dusty parts are best collected with a vacuum cleaner. Dirt and grease must be cleaned with 7110 base cleaner or a high-pressure water unit, or another cleaning method.</p><p>Absorbent substrates must be primed with a solution in the ratio of 1 part 4180 primer to 3 parts water. On non-absorbent surfaces, apply 4140 primer in concentrated form. Wooden surfaces must be primed with concentrated 4180 primer. The surface must be primed before each subsequent x-plan layer application. Apply the primer to the surface with a brush.</p><p>15 kg of powder must be mixed with 3.6 – 3.7 l of clean water. The mixture must be stirred for 2 minutes with a slow-rotating mixer or a pump mixer until a homogeneous mass is obtained. The mixed compound must be applied within approximately 20 – 30 minutes at room temperature from +10 to +20 °C. Apply the compound immediately after mixing. The applied compound levels itself, but can also be smoothed afterwards and leveled in corners with a smooth spatula.</p><p>For light load and light foot traffic, the surface is ready after 3 – 5 h. Drying depends on air temperature and humidity in the room. Further coating and processing of the surface can be carried out after 24 h. In bathrooms and wet rooms, the surface must be coated with the mira 4400 multicoat system.</p>
13.39 €
EUR
SKU: 206075
Brand: mira
EAN: 5701914660063
- Self-Leveling Compound with Fibers mira x-plan 25 kg 2-50mm
- Weber Floor dB PORAND 20kg 10-50mm Self-Leveling
- Non-Shrink Mortar RM 25kg
- Floor Self-Leveling Compound NSP 25kg 3-20mm for Concrete Surfaces
- Knauf Adhesive Mortar Klebespachtel P 25kg for Polystyrene
- Knauf Klebespachtel M Adhesive Mortar for Mineral Wool 25kg
- Adhesive and Reinforcing Mortar BAK-F Anti-Frost Grey 25kg
- Adhesive Mortar for Insulation Boards Kleber PM 25kg
- Java CN71 25kg Floor Self-Leveling Compound 0.5-10mm
- Concrete Clone Weber S100 25kg
- Java CT29 25kg Mineral Filler
- Mortar for Floors RS88 25kg Fast-Setting 1-100 mm
This product is available at Zum.lv - the largest online store in Latvia.
View product on site