Masonry Mortar ZF 25kg Winter
Cement mortar for masonry with anti-frost additive:<ul><li>For work at temperatures down to -10°C</li><li>Cement-based</li><li>For masonry, plastering and repair work</li><li>Plastic when applied</li><li>Excellent mechanical and climatic resistance</li><li>Suitable for chimney masonry</li><li>Grey colour</li><li>High hydrophobicity and water vapour permeability</li></ul>Application:<ul><li>The substrate must be firm, stable and crack-free</li><li>Blocks or bricks must be clean and dry, they must not be iced or frozen</li><li>Clean the substrate from less stable and/or detachable layers</li><li>Particularly dense and/or smooth substrates must be treated with an abrasive material</li><li>Highly water-absorbent surfaces must be primed with SAKRET BG primer or SAKRET UG primer (diluted at a ratio of 1:3)</li><li>Particularly smooth concrete surfaces must be primed with SAKRET QG primer</li><li>Mix SAKRET ZF in a clean container with cold water (use warm water in winter conditions) until a homogeneous lump-free mass is formed</li><li>It is recommended to use a mixer at 600 rpm</li><li>The temperature of the building mix at the time of laying must not be lower than +8°C</li><li>After completion of work, structures must be covered immediately, first with a waterproofing and then with a thermal insulating material, e.g. polyethylene film and mineral wool boards</li><li>The temperature of any substrate or formwork must be such that the concrete does not freeze before reaching the critical or calculated temperature during hardening, min. +5°C</li><li>Mortars with a class not lower than M5 must be used</li><li>All bricks and blocks must be cleaned of snow and ice before laying</li><li>It is recommended to carry out a thermal calculation of the concrete structure (concrete cooling time, required thermal insulation properties, concrete placement temperature)</li><li>Above +5°C, the anti-frost additive acts as a hardening accelerator</li><li>Technical data refers to +20°C temperature and 50% relative air humidity. Lower temperature increases, higher temperature decreases the stated values</li><li>During the mortar hardening phase, protect from sunlight, drafts and excessively high temperatures (>30°C)</li><li>Protect fresh mortar from rain and excessively rapid drying</li><li>Once the mortar has started to set, no more water may be added</li><li>Immediately after use, wash containers and tools with water</li><li>Hardened mortar can only be removed mechanically</li><li>Contains cement, reacts alkalinely</li><li>Protect skin and eyes, follow technical instructions. If mortar gets into eyes, rinse with large amounts of water, consult a doctor if necessary</li><li>Protect packaging from weather conditions, store on wooden pallets in a cool and dry place, cover torn packaging immediately</li></ul>Technical Data:<ul><li>Strength class (according to standard LVS EN 998-1) CS IV</li><li>Strength class (according to standard LVS EN 998-2) M10</li><li>Grain size ≤2 mm</li><li>Volume of ready mortar (25 kg) ~ 15 l</li><li>pH 11 - 13.5</li><li>Drying time for 1mm plaster layer 24 h</li><li>Full strength achieved in 28 days</li><li>Fire resistance class A1 (non-combustible)</li></ul>
5.99 €
EUR
SKU: 16726
Brand: Sakret
EAN: 4751006562080
- Lime-Cement Mortar 40kg PM Super
- Masonry Mortar Weber M100/600 25kg Winter
- Concrete Weber 25kg Base10 for Floors
- Weber floor110 fine 20kg 4-30mm self-leveling
- Adhesive for Aerated Concrete Blocks Porenbetonkleber 25kg White
- Self-leveling compound mira 6700 cemplan 25 kg 1-45mm
- Self-leveling compound mira 6600 cemplan 15 kg 0-10mm
- Self-Leveling Compound with Fibers mira x-plan 25 kg 2-50mm
- Weber Floor dB PORAND 20kg 10-50mm Self-Leveling
- Non-Shrink Mortar RM 25kg
- Floor Self-Leveling Compound NSP 25kg 3-20mm for Concrete Surfaces
- Knauf Adhesive Mortar Klebespachtel P 25kg for Polystyrene
This product is available at Zum.lv - the largest online store in Latvia.
View product on site