Tile Adhesive Knauf K2 25kg Flexible

<p>Flexible, water and frost resistant, thin-layer, high-quality cement-based tile adhesive. Knauf K2 is a mixture of dolomite and natural sand with cement, enriched with polyvinyl acetate polymer and additives to improve the properties of the mass.</p><u>Technical Data:</u><ul><li>Complies with standard LVS EN 12004, type C2TE</li><li>Fire reaction class A1, non-combustible</li><li>Adhesion to concrete ≥ 1.0 N/mm²</li><li>Slip < 0.5 mm</li><li>Layer thickness 2 - 8 mm</li><li>Tile laying time approximately 30 min</li><li>Air and substrate temperature during application and drying must be between +5°C and +25°C</li><li>Packaging 25 kg</li></ul><u>Properties and Application Area:</u><ul><li>Flexible</li><li>High initial bond</li><li>No shrinkage or stress</li><li>Water resistant</li><li>Frost resistant</li><li>With extended laying time</li><li>With reduced slip < 0.5 mm</li><li>Hydraulically hardening</li><li>For manual application</li><li>For interior and exterior use</li><li>Thin-layer tile adhesive suitable for walls and floors, also applicable for heated floors</li><li>Suitable for loaded, stable surfaces, gypsum boards (mounted on walls in two layers)</li><li>Intended for bonding water-absorbing and non-absorbing ceramic tiles and slabs, degreased, opaque natural stone slabs</li></ul><u>Application:</u><p>The substrate must be smooth, firm, frost-free, and free of dust, paint, and oil residues. If tiling plastered surfaces, the plaster must be applied at least 10 mm thick, in one coat and left unsmoothed.</p><p>Highly absorbent and absorbent substrates should be primed with Knauf Spezialhaftgrund (diluted 1:2 with water) or Knauf Haftemulsion (diluted 1:4 with water), or Knauf Tiefengrund. Non-absorbent surfaces – polished concrete, terrazzo, etc. – should be primed with Knauf Spezialhaftgrund (undiluted) or Knauf Haftemulsion (diluted 1:2 with water). For surfaces where moisture exposure is expected, apply waterproofing Knauf Flächendicht or Knauf Flex-Dicht.</p><p>Tile only after the primer has fully dried!</p><p>Pour K2 25 kg into 6.5 - 7.5 l of clean, cold water, mix by hand or with a slow-rotating mixer until a homogeneous, lump-free mass is formed, allow to swell for 5 min and mix again. Adjust consistency by adding powder or water to the mixture.</p><p>First, apply the mixed adhesive with a trowel or spatula to the entire prepared surface at the appropriate layer thickness. Then, holding the trowel at a 90° angle, comb with a suitable notched spatula (notch sizes indicated in the Consumption table). Place the tiles into the adhesive layer and press firmly with a slight twisting motion. If a skin forms (check with a finger!), the adhesive must be reapplied. The laying and correction time depends on the absorption capacity of the substrate and tiles, as well as the air temperature. For exterior work and on floors, the tile adhesive must ensure adhesion over the entire tile surface. In these cases, apply the tile adhesive to both the tile and the substrate.</p><p>Use only clean tools and containers!</p><p>Heated floor heating must be commissioned before tiling. Heated floor systems must be switched on at maximum temperature for at least 24 hours before tiling begins. It must be switched off and cooled down before work begins. Full heating may be switched on no sooner than 28 days after tiling.</p><p>Grouting may only be carried out after the adhesive has hardened – for wall tiles no earlier than 1 day, and for floor tiles after 2 days.</p>
10.29 € EUR 9.29 € EUR (-10%)
SKU: 11382
Brand: Knauf
EAN: 4750614005989

This product is available at Zum.lv - the largest online store in Latvia.

View product on site