Tile Adhesive Knauf K4 5kg Extra Flexible

<p>Extra flexible, water and frost resistant, thin-layer, high-quality cement-based tile adhesive. Knauf K4 is a mixture of dolomite and natural sand with cement, enriched with polyvinyl acetate polymer and additives to improve the properties of the mass.</p><u>Technical Data:</u><ul><li>Complies with standard LVS EN 12004, type C2TS1</li><li>Fire reaction class A1, non-combustible</li><li>Adhesion to concrete ≥ 1.0 N/mm²</li><li>Slip < 0.5 mm</li><li>Layer thickness 2 - 8 mm</li><li>Tile laying time approximately 15 min</li><li>Air and substrate temperature during application and drying must be between +5°C and +25°C</li><li>Packaging 5 kg</li></ul><u>Properties and Application Area:</u><ul><li>Extra flexible</li><li>High initial bond strength</li><li>No shrinkage or tension</li><li>Water resistant</li><li>Frost resistant</li><li>With reduced slip < 0.5 mm</li><li>Hydraulically hardening</li><li>For manual application</li><li>For interior and exterior work</li><li>Thin-layer tile adhesive suitable for walls and floors, designed for heated floors</li><li>Suitable for flexible surfaces – Knauf dry floors, gypsum boards (mounted on wall in a single layer), moisture-resistant wood surfaces following the relevant instructions, surfaces subject to rapid temperature fluctuations, heating plinths, terraces and balconies, surfaces subject to direct moisture exposure, applicable for tile-on-tile installation</li><li>Intended for bonding water-absorbent and non-absorbent tiles, degreased and opaque natural stone slabs, clinker facing tiles – for exterior work</li></ul><u>Application:</u><p>The substrate must be smooth, firm, frost-free, and free of dust, paint and oil residues. If tiling plastered surfaces, the plaster must be applied at least 10 mm thick, in a single coat and left unsmoothed.</p><p>Highly absorbent and absorbent substrates should be primed with Knauf Spezialhaftgrund (diluted 1:2 with water) or Knauf Haftemulsion (diluted 1:4 with water), or Knauf Tiefengrund. Non-absorbent surfaces – ground (polished) concrete, terrazzo, etc. – should be primed with Knauf Spezialhaftgrund (undiluted) or Knauf Haftemulsion (diluted 1:2 with water). For surfaces where moisture exposure is expected, apply waterproofing Knauf Flächendicht or Knauf Flex-Dicht.</p><p>Tile only after the primer has fully dried!</p><p>Pour K4 25 kg into 6-7 l of clean, cold water, mix by hand or with a slow-rotating mixer until a homogeneous lump-free mass is formed, allow to swell for 5 min and mix again. Adjust consistency by adding powder or water to the mixture.</p><p>First apply the mixed adhesive with a trowel or spatula over the entire prepared surface at the appropriate layer thickness. Then, holding the trowel at a 90° angle, comb through with a suitable notched spatula (notch sizes are indicated in the Consumption table). Place the tiles into the adhesive layer and press firmly with a slight twisting motion. If a skin forms on the adhesive (check with a finger!), the adhesive must be reapplied. The working and correction time depends on the absorbency of the substrate and tiles, as well as the air temperature. When bonding tile-on-tile, the old surface must be cleaned with Knauf Intensiv Reiniger. For exterior work and on floors, the tile adhesive must ensure adhesion across the entire tile surface. In these cases, apply tile adhesive to both the tile and the substrate.</p><p>Use only clean tools and containers!</p><p>When tiling wooden surfaces, such as plank floors, OSB or chipboard panels, the wooden substrate must be protected against moisture. When tiling wooden floors, the maximum tile size is 30x30 cm. Tongue-and-groove impregnated chipboard panels must be used, fixed firmly to the substrate. Direct tiling of chipboard panels is only permitted on walls, with Knauf Spezialhaftgrund primer applied, but even in this case it is recommended to first cover them with gypsum boards. When tiling floors, direct bonding of tiles to planks, OSB or chipboard panels is not permitted. In this case, an intermediate layer should be formed using the waterproofing membrane Knauf Abdichtungs-& Entkopplungsbahn, or with Knauf Brown, or with Knauf Aquapanel® Cement Board Floor The Underlay boards, or by pouring the self-leveling material Knauf Fließspachtel Faserflex in a layer of at least 5 mm.</p><p>The heating of heated floors must be commissioned before tiling. Heated floor systems must be switched on at maximum temperature for at least 24 hours before tiling begins. Before starting work, it must be switched off and allowed to cool. Full heating may be switched on no sooner than 28 days after tiling.</p><p>Grouting may only be carried out after the adhesive has hardened – approximately after 1-2 days.</p>
5.59 € EUR 5.19 € EUR (-7%)
SKU: 17714
Brand: Knauf
EAN: 4750614006191

This product is available at Zum.lv - the largest online store in Latvia.

View product on site