Tile adhesive mira 3130 superfix extra flexible, white 15 kg
<p>White, non-slump tile adhesive with excellent adhesion and flexibility. Suitable for substrates with increased risk of deformation, such as fireplaces, heated floors, natural stone, etc. Suitable for bonding all types of ceramic tiles, clinker and natural stone, for interior and exterior use. On floors and walls, in wet and dry areas. Specially suited for heated and high-temperature surfaces, as well as thin almost transparent tiles, glass mosaic, marble, and glass blocks.</p><u>Properties:</u><ul><li>Highest flexibility class (S2)</li><li>White cement base</li><li>Polymer reinforced</li><li>Good adhesion</li><li>Water resistant</li><li>Non-slump – tiles will not slide</li><li>Suitable for natural stone and glass mosaic</li><li>Long correction time</li><li>Frost resistant</li><li>Average consumption for walls 2.5 kg/m², for floors 3.5 kg/m²</li><li>Application temperature +10 to +25°C</li><li>Working time 6 h</li><li>Hardening for further processing after 10 - 24 h</li><li>Fully hardened after 7 days</li></ul><u>Application:</u><p>Intended for floors and walls with moderate deformation and surface tension, plastered brick and block walls, gypsum board panels, concrete elements, surfaces with moderate shrinkage, movement and deformation.</p><p>The substrate must be firm, dry, hard, and free from dust, dirt, grease, etc. When tiling over old tiling or a painted surface, ensure the adhesive bond is suitable for that surface. It is recommended to clean the surface of grease and other contaminants using 7110 base cleaner. The substrate is primed with 4180 primer; in wet rooms in accordance with applicable regulations, ETAG 022 and mira installation recommendations.</p><p>15 kg of powder should be mixed with 3.75 – 4.2 l of clean water and stirred until a homogeneous lump-free mass is obtained. It is recommended to use an adhesive mixer for mixing. It is advisable to observe the minimum and maximum working temperatures for the dry powder, water and substrate. After mixing, the adhesive must be used within 6 h. It is not recommended to apply adhesive to larger areas than can be tiled before the skinning effect appears. The 3130 adhesive should be applied to the substrate with the smooth side of the trowel and spread evenly over the surface, then combed with the notched side of the trowel. The notch size depends on the tile size and the base surface. Press the tiles into the wet adhesive with a slight movement. For areas exposed to moisture such as terraces, balconies, facades, and swimming pools, adhesive should be applied to both the tiles and the substrate. To achieve 100% coverage, check that the back of the tile is fully covered. In areas larger than 36 m² and spans greater than 8 m, it is advisable to install expansion joints in accordance with good construction practice. Joints can be grouted after a period of time depending on the absorption of the tiles and substrate and the air temperature (for walls approx. 10 h, for floors approx. 18 h).</p>
25.09 €
EUR
SKU: 206066
Brand: mira
EAN: 5701914313020
- Tile Adhesive Mira Unifix 3110 25kg Flexible White
- Tile Adhesive Mira Unifix 3110 5kg Elastic White
- Tile Adhesive mira 3100 unifix (C2T) Grey 25 kg
- Tile adhesive mira 3130 superfix extra flexible, white 5 kg
- Tile Adhesive FKE Flexible 25kg Grey
- Tile Adhesive Knauf K2 25kg Flexible
- Tile Adhesive Knauf K4 25kg Extra Flexible
- Knauf Perlfix 12kg Plasterboard Adhesive
- Knauf Perlfix 30kg Plasterboard Adhesive
- Tile Adhesive FK 25kg Grey
- Tile Adhesive Tilecol 24A 310ml Ready-to-Use
- Tile Adhesive FFK Extra Flexible 25kg
This product is available at Zum.lv - the largest online store in Latvia.
View product on site