Tile Adhesive Knauf K2 12kg Flexible
<p>Flexible, water and frost resistant, thin-layer, high-quality cement-based tile adhesive. Knauf K2 is a mixture of dolomite and natural sand with cement, enriched with polyvinyl acetate polymer and additives to improve the properties of the compound.</p><u>Technical Data:</u><ul><li>Complies with standard LVS EN 12004, type C2TE</li><li>Fire reaction class A1, non-combustible</li><li>Adhesion to concrete ≥ 1.0 N/mm²</li><li>Slip < 0.5 mm</li><li>Layer thickness 2 - 8 mm</li><li>Tile laying time approximately 30 min</li><li>Air and substrate temperature during application and drying must be between +5°C and +25°C</li><li>Packaging 12 kg</li></ul><u>Properties and Application Area:</u><ul><li>Flexible</li><li>High initial bond</li><li>No shrinkage or stress</li><li>Water resistant</li><li>Frost resistant</li><li>With extended open time</li><li>With reduced slip < 0.5 mm</li><li>Hydraulically hardening</li><li>For manual application</li><li>For interior and exterior use</li><li>Thin-layer tile adhesive suitable for walls and floors, also applicable for heated floors</li><li>Suitable for heavily loaded, stable surfaces, gypsum boards (mounted on walls in two layers)</li><li>Intended for bonding water-absorbing and non-absorbing ceramic tiles and slabs, and degreased, opaque natural stone slabs</li></ul><u>Application:</u><p>The substrate must be smooth, firm, frost-free, and free from dust, paint, and oil residues. If tiling over plastered surfaces, the plaster must be applied at least 10 mm thick, in one coat, and left unsmoothed.</p><p>Highly absorbent and absorbent substrates should be primed with Knauf Spezialhaftgrund (diluted 1:2 with water) or Knauf Haftemulsion (diluted 1:4 with water), or Knauf Tiefengrund. Non-absorbent surfaces – polished (burnished) concrete, terrazzo, etc. – should be primed with Knauf Spezialhaftgrund (undiluted) or Knauf Haftemulsion (diluted 1:2 with water). For surfaces exposed to moisture, apply waterproofing Knauf Flächendicht or Knauf Flex-Dicht.</p><p>Only begin tiling after the primer has fully dried!</p><p>Pour K2 25 kg into 6.5 - 7.5 l of clean, cold water, mix by hand or with a slow-rotating mixer until a uniform lump-free consistency is achieved, allow to slake for 5 min, then mix again. Adjust consistency by adding powder or water to the mixture.</p><p>First, apply the mixed adhesive with a trowel or spatula over the entire prepared surface at the appropriate layer thickness. Then, holding the trowel at a 90° angle, comb through with a suitable notched trowel (notch sizes indicated in the Consumption table). Place the tiles into the adhesive bed and press firmly with a slight twisting motion. If a skin forms (check with a finger!), the adhesive must be reapplied. Open and correction time depends on the absorption capacity of the substrate and tiles, as well as air temperature. For exterior use and on floors, the tile adhesive must provide full coverage across the entire tile surface. In these cases, apply tile adhesive to both the tile and the substrate.</p><p>Use only clean tools and containers!</p><p>Heated floor heating must be commissioned before tiling. Heated floor systems must be switched on at maximum temperature for at least 24 hours before tiling begins. It must be switched off and allowed to cool before work starts. Full heating may not be switched on until at least 28 days after tiling.</p><p>Grouting may only be carried out after the adhesive has hardened – for wall tiles no earlier than 1 day, and for floor tiles after 2 days.</p>
6.39 € EUR
5.75 € EUR
(-10%)
SKU: 17716
Brand: Knauf
EAN: 4750614006221
- Tile adhesive mira 3130 superfix extra flexible, white 15 kg
- Tile Adhesive Mira Unifix 3110 25kg Flexible White
- Tile Adhesive Mira Unifix 3110 5kg Elastic White
- Tile Adhesive mira 3100 unifix (C2T) Grey 25 kg
- Tile adhesive mira 3130 superfix extra flexible, white 5 kg
- Tile Adhesive FKE Flexible 25kg Grey
- Tile Adhesive Knauf K2 25kg Flexible
- Tile Adhesive Knauf K4 25kg Extra Flexible
- Knauf Perlfix 12kg Plasterboard Adhesive
- Knauf Perlfix 30kg Plasterboard Adhesive
- Tile Adhesive FK 25kg Grey
- Tile Adhesive Tilecol 24A 310ml Ready-to-Use
This product is available at Zum.lv - the largest online store in Latvia.
View product on site